plc.net.ru

SIMATIC WinCC flexible 2007 is the innovative HMI software under Windows for all machine-oriented and process-oriented applications of the machine, series machine and plant construction. The engineering software enables the integrated configuration of all HMI operator devices ranging from the Micro Panel up to the PC-based visualization -all of this with the highest level of configuration efficiency.

Для работы с PLCSIM на одном компе требуется настроить программный интерфейс аналогично рекомендациям по Протулу

I think CoMod hast not yet released this version

Новые Ключи появятся в списке только после установки новой программы !
Пока программа не установлены новые ключи не будут показаны в списке.
Смотри на примере ниже WinCC Flexible 2007 = v1.2 !

Hotfix 2 also contains the corrections of previous hotfixes 1 for WinCC flexible 2007.

Problems corrected with Hotfix 2
Problems corrected in the Engineering System and optimization of configuration scenarios with this Hotfix:
● Symbolic addressing of variables in an instance DB is not possible. Corrupt constant prevents reliable addressing of instance data blocks.
● Graphic fonts cannot be used in screen elements. Graphic fonts, such as Wingdings or Symbol, cannot be used for screen elements in a project. You will be able to select the font but the font will be reset after confirmation.
● Project documentation cannot be printed for converted ProAgent projects. Project documentation will remain empty if users try to print a converted ProAgent project in WinCC flexible 2007 without ProAgent.
● Problems in WinCC flexible when using the Logitech SetPoint mouse software WinCC flexible 2007 will crash if the Logitech SetPoint software has been installed and enabled and users move the mouse wheel in the screen editor.

Runtime problems resolved with this Hotfix and corresponding optimization of behavior:
● Use of MMC card (6AV6671-1CB00-0AX1, ES:01) is not stable for the following HMI devices: – OP 77B – OP 177B – TP 177B – Mobile Panel 177 – OP 277 – TP 277
● Restore using OP177B DP mono A "Restore" via the Control Panel may not function correctly under certain circumstances for the OP 177B DP mono.
● Gauges are incorrectly displayed in faceplates.

Problems corrected with Hotfix 1
Problems resolved and optimization of configuration scenarios with this Hotfix:
● Update error of faceplates An update error occurs when lines, polygons or polylines are used in a faceplate following an update. The respective lines, polygons and polylines will be missing from all screens not open currently when this faceplate is used in runtime. The changes will be visible in the Engineering System immediately.
● Incorrect display of text fields If configured text fields use the same font (e.g. Tahoma) but are not formated in the same way (e. g. bold, italics), these text fields will still be displayed as identical fields in runtime.
● Linear scaling with S5TIME Linear scaling is not used for variables of data type S5TIME in runtime even though this option is available in the Engineering System.
● Adress synchronization for stations of 400 series Address synchronization of WinCC flexible is aborted if a redundant station of the 400 series, type 6ES7 417-4HL04 0AB0 / V4.0 or 6ES7 414-4HJ04 0AB0 / V4.0, is present in a Step7 project.

Hello again Sania...Well, this is the message when I try to install "WinCC Flexible 2007" in my Windows XP Professional SERVICE PACK 3.

"The software cannot be installed on your computer with the operating system Windows XP Professional Service Pack 3, v.3311.

One of the following Microsoft operating systems has to be installed:
Windows 2000 Service Pack or higher, Windows XP Professional Service Pack 2 or higher."


My solution is uninstall Service pack 3 or I set something before installing?
I opened "Setups.ini" and this is part of the code on file.


WinXP is enabled by default...

Do you have another proposal?

What do I do with SP3 in windows Xp?

Thank you for trying to help me